10/17/2021 0 Comments Clear Background Image For Mac
All images used in this article were found on Unsplash. An image: Click the Background pop-up menu and choose Image Fill. Slide the squares and use the other controls to change the blend, angle, and direction of the gradient.If that’s the case, you can use any of the methods described here to polish up the result. Using Photoshop Quick Action will do most of the work for you, but the results may fall short of your expectations, depending on your image. This is new in Photoshop 2021 (in the Creative Cloud subscription) and provides a very fast way to remove backgrounds.With speed, however, comes less accuracy. Best to use with high contrast between subject and background, and when the subject has fairly simplistic lines.By far the quickest method discussed here is the built-in Photoshop Quick Action for removing backgrounds in Photoshop. By using this editor, you can get an image with a transparent background.Best to use when: you’re doing it for you, you need it fast, and you’re not necessarily looking for perfection. When you click on any area, the tool deletes the background of the same color.
For more control, you’ll have to sacrifice some time to get the desired result. While outside the scope of this article, if you need help with working with masks, check out this Adobe tutorial.Photo credit: Karsten Wingert on UnsplashBest to use when: working with high contrast images, although it takes a fair bit of time and effort to produce a good outcome.The Background Eraser tool is great if you need a bit more control over removing the background but still want Photoshop to do some of the heavy lifting for you. In the Properties panel (by default this should be above your Layers panel), click the Remove Background button under Quick Action.The quick action has now removed the background, leaving your layer with a mask around the subject.From here, you can make refinements by going into the mask and adjusting as needed (such as around the dog’s feet at the bottom left of the image). (If it was already checked, there’s no need to click it if it isn’t checked, click it to open it up on the right-hand side by default.)In your Layers panel, click your new layer. Click the eye icon to the left of the original layer to turn that layer off.Make sure your Properties panel is open by going to Window > Properties. In the dialog box that pops up, name your layer (whatever you’d like), and click OK. Still in the tool options bar at the top, set the Sampling to be Continuous. In this case, I’m starting with 50px.You can adjust it as we go by using the square brackets ( ) to decrease and increase the size of the brush. Click and hold the Eraser tool to reveal more options to and select the Background Eraser tool.In the tool options bar at the top of the screen, click the brush icon to reveal the brush panel.Change the hardness so that it’s near or at 100%.The size can be whatever you deem appropriate for the image you’re working with. This tool may be hidden below the Eraser tool. Steps:Select the Background Eraser tool from the toolbox on the left-hand side. Start erasing the background around your subject using the Background Eraser tool by clicking and holding while moving the brush. Conversely, the higher the tolerance, the more colors the tool will select. Next, set the Limits to Find Edges and the Tolerance to be somewhere in the range of 20–25%.Note that the lower the tolerance, the fewer color variations it will pick up. This is telling the brush to only use the color under the crosshairs in that moment and not resample as you go along.This process can be quick or tedious depending on your image, but provides good results, as you’re in control of determining what is the subject and what isn’t. You can do this by revisiting the tools option bar at the top, or using to adjust down and up the size of your brush.If resizing the brush doesn’t work and it’s erasing your subject, undo your action, then go into the tool options bar at the top and adjust the Sampling to Once (the middle icon in the set of three), the Limits to Discontiguous, and Tolerance to around 10%. Zoom in on the image if you need to see more close details.I recommend you do short strokes with the brush (remembering to let go of the mouse from time to time) so that you can always Undo if the brush goes too far.In the more difficult areas, you may find that you need to adjust the size of your brush as you go. Codec pack for media player macSteps:Select the Pen tool from the toolbox on the left-hand side (above the Text tool). Because it gives you the most control, it can also be the most time-consuming and requires patience. It gives you the most control out of all the methods listed here.The Pen tool is one of the most tried and true ways in Photoshop to remove backgrounds in images, and gives you the most control over the outcome. Pen ToolBest to use when: the subject and background are not highly contrasted, or when other tools such as the Quick Action or Background Eraser tool mentioned above aren’t producing desired results. Once you’ve completed the path and you’re happy with the results, you’ll want to save the path. Then start working your way around your subject adding additional anchors to start outlining your subject.If you need to make a curved line, click-hold-drag to produce a curved line, moving the mouse to adjust the curve as needed.To adjust an anchor point or directional lines for fine tuning, use the Direct Selection tool (hidden under the Path Selection tool) in the toolbox.To undo an anchor, go to File > Undo or use your keyboard shortcut ( Command + Z for macOS, Control + Z for Windows).For more info about the Pen tool and working with paths in Photoshop, read this Adobe tutorial.Make sure you complete the path once you’re done by meeting up with your first point. Start at the edge of your subject (or a suitable starting point) and click to start the first anchor. You should now see the white/gray checkered background instead of your previous background.You may find, as with the other methods listed, that this doesn’t get you 100%. You’ll see the marching ants are now around the entire image and the subject, essentially selecting the background.To delete the background, press Delete. This will give you the marching ants outline where your path was.Since we don’t want to delete what’s inside the selection, we’ll want to change the selection to be everything except the subject. Now your path is saved in the Paths panel.Next, right click your new path in the Paths panel and select Make Selection, then click OK in the dialog box (leave all defaults for now). Click the three bar menu at the right and click New Path, and name your path. The selection will then turn into marching ants around your selection.Save your selection by going to Selection > Save Selection and giving it a name.
0 Comments
Leave a Reply. |
AuthorLaurel ArchivesCategories |